Talk:PriusPlus-Mechanical - Revision history

Cewert: updated todo

2007-06-16T16:06:36Z

updated todo

Cewert: todos

2007-06-04T03:21:11Z

todos

Cewert: more todos

2007-05-27T22:35:05Z

more todos

71.204.141.87: listed existing LED board mounting technique

2007-05-22T03:53:42Z

listed existing LED board mounting technique

Cewert: rewrote todo

2007-05-22T02:22:03Z

rewrote todo

Cewert: starting some todo's

2007-05-22T02:13:00Z

starting some todo's

New page

This is moved here for the time being to help with organizing:

**Battery box base (Tom)
**Plastic parts mounting board (Little Jim)
**Anti arc mounted to contactor - You will need a (identifying terminology here) capacitor part number (#) and solder one side to a “ ” ohm resistor and a matching length of wire to the other side of the capacitor. Once this has been completed cover the exposed wires with shrink wrap. Finally, crimp ring connectors to each end and solder in place for a better connection. (Add photo)
**Heating pad power boxes (Ron, can this now be shrunk down to a single three outlet box?)
**Charger mounting
**Battery box mounting (Tom)
**Power cord mounting (Little Jim or Tom)
**Amp meter mounting (Ron is the amp meter still needed? Should we put this as optional?)
**Diagnostic LEDs mounting - Use Velcro to mount it just inside the glass door under the radio. To run the ribbon cable, open up the dash and run a cable as shown it this diagram. (Make and add diagram.)
**V4 Screen mounting
**[[CAN-View]] mounting
**Prius disassembly and reassembly

@@ Line 3: / Line 3: @@
 Todo (high priority):
 Someone who has done a "classic" PriusPlus conversion needs to do the following:
 # Write up battery box base mounting for alt. mounting method (Chris)

@@ Line 2: / Line 2: @@
 Todo (high priority):
-# Write up battery box base mounting
+Someone who has done a "classic" PriusPlus conversion needs to do the following:
-# Write up mounting the GFCI outlet box (wiring to be on electrical)
+# Verify battery box base mounting
 # Write up mounting the charger
 # Write up assembly of electronics tray plastic
 # Write up the mounting of the electronics tray
-# Write up Prius re-assembly instructions.
 # Write up battery box base mounting for alt. mounting method (Chris)
@@ Line 15: / Line 16: @@
 Todo (low priority):
 # Write up mounting the cord reel
 # Write up installing the bumper inlet (options for front or rear + routing cables)

@@ Line 3: / Line 3: @@
 Todo (high priority):
 # Write up battery box base mounting
 # Write up mounting the GFCI outlet box (wiring to be on electrical)
 # Write up mounting the charger
 # Write up assembly of electronics tray plastic
-# Write up assembly of electronics box plastic for alt. mounting method
+# Write up the mounting of the electronics tray
-# Write up how to dissassemble the trunk (flooring on OEM battery, both side panels, opening the OEM battery (include HV warning), removal of kick panels for routing cables from front to rear of car.)  Also needs re-assembly instructions.
+# Write up Prius re-assembly instructions.
 Todo (low priority):
 # Write up Amp meter mounting (to be listed as optional)
 # Write up diagnostic LEDs board mounting - Use self-tapping screws to mount it to the roof of the tray just inside the glass door under the radio. To run the ribbon cable, open up the dash and run a cable as shown it this diagram [or drill a hole in the back of the tray, at the upper left as you look at it].  (Make and add diagram.)
 # V4 Screen mounting (low priority because it can be found elsewhere)

@@ Line 15: / Line 15: @@
 Todo (low priority):
 # Write up Amp meter mounting (to be listed as optional)
-# Write up diagnostic LEDs board mounting - Use Velcro to mount it just inside the glass door under the radio. To run the ribbon cable, open up the dash and run a cable as shown it this diagram.  (Make and add diagram.)
+# Write up diagnostic LEDs board mounting - Use self-tapping screws to mount it to the roof of the tray just inside the glass door under the radio. To run the ribbon cable, open up the dash and run a cable as shown it this diagram [or drill a hole in the back of the tray, at the upper left as you look at it].  (Make and add diagram.)
 # V4 Screen mounting (low priority because it can be found elsewhere)

@@ Line 1: / Line 1: @@
-This is moved here for the time being to help with organizing:
+This is here for the time being to help with organizing:
-**Battery box base (Tom)
+Todo (high priority):
-**Plastic parts mounting board (Little Jim)
+# Write up battery box base mounting
-**Anti arc mounted to contactor - You will need a (identifying terminology here) capacitor part number (#) and solder one side to a “ ” ohm resistor and a matching length of wire to the other side of the capacitor. Once this has been completed cover the exposed wires with shrink wrap.  Finally, crimp ring connectors to each end and solder in place for a better connection.  (Add photo)
+# Write up battery box base mounting for alt. mounting method
-**Heating pad power boxes (Ron, can this now be shrunk down to a single three outlet box?)
+# Write up mounting the GFCI outlet box (wiring to be on electrical)
-**Charger mounting
+# Write up mounting the charger
-**Battery box mounting (Tom)
+# Write up mounting the charger alt. mounting method
-**Power cord mounting (Little Jim or Tom)
+# Write up mounting the cord reel
-**Amp meter mounting (Ron is the amp meter still needed?  Should we put this as optional?)
+# Write up installing the bumper inlet (options for front or rear + routing cables)
-**Diagnostic LEDs mounting - Use Velcro to mount it just inside the glass door under the radio. To run the ribbon cable, open up the dash and run a cable as shown it this diagram.  (Make and add diagram.)
+# Write up assembly of electronics tray plastic
-**V4 Screen mounting
+# Write up assembly of electronics box plastic for alt. mounting method
-**[[CAN-View]] mounting
+# Write up how to dissassemble the trunk (flooring on OEM battery, both side panels, opening the OEM battery (include HV warning), removal of kick panels for routing cables from front to rear of car.)  Also needs re-assembly instructions.
-**Prius disassembly and reassembly