General Disclaimer: (HV) (DC) injury or death hazard, use at your own risk, may void warranty. |
All public logs
Jump to navigation
Jump to search
Combined display of all available logs of My wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)- 15:23, 21 March 2007 Cewert talk contribs uploaded File:Electronics Box Partial 1.jpg (Mostly completed electronics box without top. This is for the alt. mounting method.)
- 21:44, 20 March 2007 Cewert talk contribs uploaded File:Entire alt batt box mounting supports.jpg (Alt. mounting method. Shows supports with trays in place.)
- 21:42, 20 March 2007 Cewert talk contribs uploaded File:Rubber on center batt box support.jpg (Alt mounting method. Shows rubber pads on the battery box support.)
- 21:41, 20 March 2007 Cewert talk contribs uploaded File:Left side battery box supports alt method.jpg (Alt mounting method. Shows left side of battery box supports)
- 21:40, 20 March 2007 Cewert talk contribs uploaded File:Right side battery box supports alt method.jpg (Alt. mounting method. Shows right side of supports)
- 21:39, 20 March 2007 Cewert talk contribs uploaded File:Alt method support angle irons.jpg (Alt. mounting method showing all angle irons (does not have angle iron on center support yet.)
- 21:37, 20 March 2007 Cewert talk contribs uploaded File:Welded angle iron 2.jpg (Shows just the welded angle iron for alt. mounting method)
- 21:36, 20 March 2007 Cewert talk contribs uploaded File:Welded angle iron 1.jpg (The welded steel angle iron is supporting the aluminum angle irons that support the battery box.)
- 19:49, 20 March 2007 Cewert talk contribs uploaded File:Charger in tirewell.JPG (Alt. mounting method. Charger is in tire well on steel sheet. Also shows outter batt box supports)
- 04:15, 13 February 2007 Cewert talk contribs uploaded File:Batt box test fit forward design.JPG (Test fitting (and partially mounted) battery box. The battery box is moved as forward as possible.)
- 04:13, 13 February 2007 Cewert talk contribs uploaded File:Bracket on OEM Batt screw.JPG (Bracket on OEM battery mounts I used to hold down new battery box)
- 04:09, 13 February 2007 Cewert talk contribs uploaded File:Batt Box with screw lift supports.JPG (Battery box set together with supports for screw lift idea)
- 04:07, 13 February 2007 Cewert talk contribs uploaded File:P1240040.JPG (Battery box from side set together)
- 19:44, 12 January 2007 Cewert talk contribs uploaded File:JTN60060 Fuse Holder.JPG (JTN60060 Fuse Holder)
- 19:41, 12 January 2007 Cewert talk contribs uploaded File:JTN60060 Fuse Holder.JPG (JTN60060 Fuse Holder)
- 19:39, 12 January 2007 Cewert talk contribs uploaded File:LPJ-60SP.JPG (The 60 amp LPJ-60SP fuse)
- 19:06, 12 January 2007 Cewert talk contribs uploaded File:EV200 Contactor.JPG (The Kilovac EV200A4ANA (EV200) contactor)
- 19:05, 12 January 2007 Cewert talk contribs uploaded File:Bottom of JTN60060.JPG (Bottom of the fuse holder)
- 19:03, 12 January 2007 Cewert talk contribs uploaded File:Fuse in holder.JPG (Installing the fuse into the holder)
- 19:01, 12 January 2007 Cewert talk contribs uploaded File:Fuses and Holders.JPG (The fuses and holders)
- 23:02, 17 December 2006 Cewert talk contribs uploaded File:Mostly Finished Batt Box.JPG (Mostly finished battery box. Holes still need to be drilled into the angle irons to bolt down, and bolts will be added in the middle between the trays to bolt the top of the pack to the bottom. Also, mounting frame is not completely cut to size.)
- 23:00, 17 December 2006 Cewert talk contribs uploaded File:Batt Box with Bolt Down Angle.JPG (Shows the aluminum angle iron that sicks out of each side to bolt the battery box top down to the car. Waiting to drill holes until it is actually mounted.)
- 22:57, 17 December 2006 Cewert talk contribs uploaded File:Finished Corner.JPG (Finished corner with ground of screws. I'm pretty sure this isn't done the official CalCars method.)
- 22:56, 17 December 2006 Cewert talk contribs uploaded File:Binding Posts Ground Down.JPG (These are the binding posts I choose to use. The one on the left is ground down to fit and the burs are also ground off. I'm sure there is a better way to do this, but it worked.)
- 22:54, 17 December 2006 Cewert talk contribs uploaded File:Inside Corner.JPG (Inside the corner bracket. The machine screws are counter sunk into the aluminum angle iron.)
- 22:53, 17 December 2006 Cewert talk contribs uploaded File:Batt Box with Bolt Down Angle.JPG (Corner bracket in place and screwed down on the top. Ready to drill holes in the side and bolt down the bracket from the sides.)
- 22:51, 17 December 2006 Cewert talk contribs uploaded File:Plexiglass Shield.JPG (I choose to install a plexiglass 'shield' on the side of the aluminum angle iron to reduce the risk of a wire / terminal hitting the aluminum and arcing. I am not sure if that is in the official CalCars plans or not. It is held in by non-conductive nylo)
- 22:43, 17 December 2006 Cewert talk contribs uploaded File:Batt Box Top 3 Angles.JPG (Aluminum angle irons cut with 45 degree angles and laid on top of the battery box)
- 05:34, 15 December 2006 Cewert talk contribs uploaded File:Top Battery Box With Corner Bracket.JPG (Corner bracket is just sitting on the top of the battery box waiting to be screwed down.)
- 05:33, 15 December 2006 Cewert talk contribs uploaded File:Top Battery Box 45 Degree Cuts.JPG (The aluminum angle irons are cut with 45 degree angles so they fit snugly)
- 05:31, 15 December 2006 Cewert talk contribs uploaded File:Starting on the Top of Battery Box.JPG (Bottom is mostly assembled, now starting on cutting the angle irons for the top.)
- 05:29, 15 December 2006 Cewert talk contribs uploaded File:2 Trays with Some Supports.JPG (2 of the trays sitting on 2 1-1/2 angle irons (others just sitting there))
- 05:19, 15 December 2006 Cewert talk contribs uploaded File:4 Finished Trays.JPG
- 05:18, 15 December 2006 Cewert talk contribs uploaded File:Finished Tray.JPG
- 05:17, 15 December 2006 Cewert talk contribs uploaded File:Screws Sticking Through Partially Assembled Tray.JPG (I used extra long, self threading screws, so they stick through. I used a hacksaw first, and then a dremel with a metal cut off attachment to cut the screws at the base. Then used a grinder to grind them perfectly flat.)
- 05:14, 15 December 2006 Cewert talk contribs uploaded File:Closeup of Sample Finished Corner.JPG (This is just a sample I tried on a scrap pieces before doing the real thing.)
- 05:12, 15 December 2006 Cewert talk contribs uploaded File:Holes drilled in aluminum.JPG (Holes drilled in the aluminum. Used the dremel to drill through both angle irons in the same place, then drilled a larger hole in the top (so the screw would go through without threading and then countersunk it with a much larger drill bit.)
- 05:10, 15 December 2006 Cewert talk contribs uploaded File:Tray Parts Laid Out.JPG (All the parts of one tray laid out)
- 05:08, 15 December 2006 Cewert talk contribs uploaded File:Dremel Drill Press.JPG (This is the Dremel drill press I used to drill the small holes in the angle irons.)
- 05:06, 15 December 2006 Cewert talk contribs uploaded File:Almost Finished Tray Jig.JPG
- 05:04, 15 December 2006 Cewert talk contribs uploaded File:Making Tray Jig Step 3.JPG (Place wood to hold the channel irons in place)
- 05:02, 15 December 2006 Cewert talk contribs uploaded File:Making Tray Jig Step 1.JPG (Step one is to place wood around the outsides of the angle iron to hold the angle irons in place.)
- 05:01, 15 December 2006 Cewert talk contribs uploaded File:Making Tray Jig Step 2.JPG (The set together tray with batteries and wood secured in placed around the outsides to form the jig.)
- 04:58, 15 December 2006 Cewert talk contribs uploaded File:Tray Ready for Jig.JPG (This photo is of the tray set together on a sheet of plywood (wich will be used as a jig to hold everything in place for drilling holes.)
- 04:56, 15 December 2006 Cewert talk contribs uploaded File:Tray Set Together Close Up.JPG
- 04:55, 15 December 2006 Cewert talk contribs uploaded File:Tray Set Together With Battery.JPG
- 04:54, 15 December 2006 Cewert talk contribs uploaded File:Tray Pieces.JPG (These are all the aluminum pieces needed to build the 4 battery trays.)
- 04:51, 15 December 2006 Cewert talk contribs uploaded File:Cutting Aluminum.JPG