General Disclaimer: (HV) (DC) injury or death hazard, use at your own risk, may void warranty. |
All public logs
Jump to navigation
Jump to search
Combined display of all available logs of My wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)- 22:57, 17 December 2006 Cewert talk contribs uploaded File:Finished Corner.JPG (Finished corner with ground of screws. I'm pretty sure this isn't done the official CalCars method.)
- 22:56, 17 December 2006 Cewert talk contribs uploaded File:Binding Posts Ground Down.JPG (These are the binding posts I choose to use. The one on the left is ground down to fit and the burs are also ground off. I'm sure there is a better way to do this, but it worked.)
- 22:54, 17 December 2006 Cewert talk contribs uploaded File:Inside Corner.JPG (Inside the corner bracket. The machine screws are counter sunk into the aluminum angle iron.)
- 22:53, 17 December 2006 Cewert talk contribs uploaded File:Batt Box with Bolt Down Angle.JPG (Corner bracket in place and screwed down on the top. Ready to drill holes in the side and bolt down the bracket from the sides.)
- 22:51, 17 December 2006 Cewert talk contribs uploaded File:Plexiglass Shield.JPG (I choose to install a plexiglass 'shield' on the side of the aluminum angle iron to reduce the risk of a wire / terminal hitting the aluminum and arcing. I am not sure if that is in the official CalCars plans or not. It is held in by non-conductive nylo)
- 22:43, 17 December 2006 Cewert talk contribs uploaded File:Batt Box Top 3 Angles.JPG (Aluminum angle irons cut with 45 degree angles and laid on top of the battery box)
- 22:40, 17 December 2006 Rjf talk contribs unblocked 201.18.150.92 talk (Only block an IP for about a week, others may use the same IP address.)
- 22:40, 17 December 2006 Rjf talk contribs unblocked 61.40.161.148 talk (Only block an IP for about a week, others may use the same IP address.)
- 22:39, 17 December 2006 Rjf talk contribs unblocked 220.31.100.174 talk (Only block an IP for about a week, others may use the same IP address.)
- 22:29, 17 December 2006 Rjf talk contribs deleted page Index.php (spam)
- 16:24, 16 December 2006 DavideAndrea talk contribs blocked 201.18.150.92 talk with an expiration time of indefinite (spam)
- 01:30, 16 December 2006 DavideAndrea talk contribs uploaded File:Batterypack-power-conn.jpg (Ford Escape, battery pack, power connectors)
- 01:28, 16 December 2006 DavideAndrea talk contribs uploaded File:Batterypack-data-conn.jpg (Ford Escape, data connectors)
- 01:27, 16 December 2006 DavideAndrea talk contribs uploaded File:Batterypack-open2.jpg (Ford Escape, battery open, view from the front)
- 01:25, 16 December 2006 DavideAndrea talk contribs uploaded File:Batterypack-open1.jpg (Ford Escape, battery open, front view)
- 01:24, 16 December 2006 DavideAndrea talk contribs uploaded File:Trunk-sans-battery.jpg (Ford Escape, trunk without the battery)
- 01:23, 16 December 2006 DavideAndrea talk contribs uploaded File:Batterypack-out.jpg (Ford Escape, battery lifted out of thetrunk)
- 05:34, 15 December 2006 Cewert talk contribs uploaded File:Top Battery Box With Corner Bracket.JPG (Corner bracket is just sitting on the top of the battery box waiting to be screwed down.)
- 05:33, 15 December 2006 Cewert talk contribs uploaded File:Top Battery Box 45 Degree Cuts.JPG (The aluminum angle irons are cut with 45 degree angles so they fit snugly)
- 05:31, 15 December 2006 Cewert talk contribs uploaded File:Starting on the Top of Battery Box.JPG (Bottom is mostly assembled, now starting on cutting the angle irons for the top.)
- 05:29, 15 December 2006 Cewert talk contribs uploaded File:2 Trays with Some Supports.JPG (2 of the trays sitting on 2 1-1/2 angle irons (others just sitting there))
- 05:19, 15 December 2006 Cewert talk contribs uploaded File:4 Finished Trays.JPG
- 05:18, 15 December 2006 Cewert talk contribs uploaded File:Finished Tray.JPG
- 05:17, 15 December 2006 Cewert talk contribs uploaded File:Screws Sticking Through Partially Assembled Tray.JPG (I used extra long, self threading screws, so they stick through. I used a hacksaw first, and then a dremel with a metal cut off attachment to cut the screws at the base. Then used a grinder to grind them perfectly flat.)
- 05:14, 15 December 2006 Cewert talk contribs uploaded File:Closeup of Sample Finished Corner.JPG (This is just a sample I tried on a scrap pieces before doing the real thing.)
- 05:12, 15 December 2006 Cewert talk contribs uploaded File:Holes drilled in aluminum.JPG (Holes drilled in the aluminum. Used the dremel to drill through both angle irons in the same place, then drilled a larger hole in the top (so the screw would go through without threading and then countersunk it with a much larger drill bit.)
- 05:10, 15 December 2006 Cewert talk contribs uploaded File:Tray Parts Laid Out.JPG (All the parts of one tray laid out)
- 05:08, 15 December 2006 Cewert talk contribs uploaded File:Dremel Drill Press.JPG (This is the Dremel drill press I used to drill the small holes in the angle irons.)
- 05:06, 15 December 2006 Cewert talk contribs uploaded File:Almost Finished Tray Jig.JPG
- 05:04, 15 December 2006 Cewert talk contribs uploaded File:Making Tray Jig Step 3.JPG (Place wood to hold the channel irons in place)
- 05:02, 15 December 2006 Cewert talk contribs uploaded File:Making Tray Jig Step 1.JPG (Step one is to place wood around the outsides of the angle iron to hold the angle irons in place.)
- 05:01, 15 December 2006 Cewert talk contribs uploaded File:Making Tray Jig Step 2.JPG (The set together tray with batteries and wood secured in placed around the outsides to form the jig.)
- 04:58, 15 December 2006 Cewert talk contribs uploaded File:Tray Ready for Jig.JPG (This photo is of the tray set together on a sheet of plywood (wich will be used as a jig to hold everything in place for drilling holes.)
- 04:56, 15 December 2006 Cewert talk contribs uploaded File:Tray Set Together Close Up.JPG
- 04:55, 15 December 2006 Cewert talk contribs uploaded File:Tray Set Together With Battery.JPG
- 04:54, 15 December 2006 Cewert talk contribs uploaded File:Tray Pieces.JPG (These are all the aluminum pieces needed to build the 4 battery trays.)
- 04:51, 15 December 2006 Cewert talk contribs uploaded File:Cutting Aluminum.JPG
- 08:56, 13 December 2006 Rjf talk contribs deleted page File:EAA-PHEV-PRIUS-ControlBdSchematicV3r1 061116.png (outdated)
- 08:56, 13 December 2006 Rjf talk contribs deleted page File:EAA-PHEV-PRIUS-HighPowerSchematicV3r1 061116.png (outdated)
- 08:56, 13 December 2006 Rjf talk contribs deleted page File:EAA-PHEV-PRIUS-HighPowerSchematicV3r1 061116.png (Deleted old revision 20061118003355!EAA-PHEV-PRIUS-HighPowerSchematicV3r1_061116.png.)
- 08:56, 13 December 2006 Rjf talk contribs deleted page File:EAA-PHEV-PRIUS-HighPowerSchematicV3r1 061116.png (Deleted old revision 20061117222211!EAA-PHEV-PRIUS-HighPowerSchematicV3r1_061116.png.)
- 08:53, 13 December 2006 Rjf talk contribs uploaded File:EAA-PHEV-PRIUS-HighPowerSchematic.png (These are the high power schematics from the latest PriusPlus conversion. V3r2_061210)
- 08:53, 13 December 2006 Rjf talk contribs uploaded File:EAA-PHEV-PRIUS-ControlBdSchematic.png (These are the low power control board schematics from the latest PriusPlus conversion. V3r3_061211)
- 08:42, 13 December 2006 Rjf talk contribs deleted page Talk:Main Page/ (spam)
- 21:16, 12 December 2006 Rjf talk contribs deleted page Index.php (spam)
- 18:55, 11 December 2006 Rjf talk contribs deleted page Index.php (spam)
- 18:55, 11 December 2006 Rjf talk contribs deleted page Talk:Main Page/ (spam)
- 03:59, 8 December 2006 Rjf talk contribs deleted page Talk:PriusPlus/ (ok, that's just weird.)
- 17:22, 6 December 2006 Rjf talk contribs uploaded File:Day 4 Image 9.JPG (brightness adjusted.)
- 17:22, 6 December 2006 Rjf talk contribs uploaded File:Day 4 Image 8.JPG (brightness adjusted.)